Ontario Roof Pros provides professional fascia, soffit & edge metal in Ontario, CA for residential and commercial properties across the Inland Empire. Rotted fascia in Ontario is almost never weather. In a climate with under a foot of rain a year, trim fails where water was delivered to it: a leaking gutter joint, a missing drip edge, a valley overshooting, a downspout discharging onto the board below.
So we find the delivery mechanism before replacing any wood. Skip that step and the new fascia rots on the same schedule the old one did, and the second repair costs what the first one cost with paint added on top. Sprinklers hitting a low eave belong on that list too, because we have replaced boards that never saw a drop of rain from above.
Repairs use full-length material wherever we can get it in. Rot cut back to sound wood, primer on all six sides including the cut ends, hangers reset into solid backing, and coil-wrapped aluminum in a matching color for owners who would like to stop painting the same forty feet of trim every four years. Nail holes get filled rather than painted over, and the gutter goes back on new hangers instead of into the old holes.
Soffit is a ventilation component as much as a finish, so vented panels get restored as intake instead of being sealed up for looks. Stucco soffits with screen vents painted closed get opened and re-screened, and any repair that closes an eave gets a new intake path in exchange, because a tidy soffit that suffocates the attic above it is not an improvement to anything.
The commercial equivalent of fascia is the edge metal on a parapet, and it does structural work rather than decorative work. A tested ES-1 gravel stop or coping, cleated on the outer leg with lapped and sealed splice plates, is what stops a Santa Ana night from lifting the membrane edge off the wall and taking the first sheet of membrane with it at two in the morning.
Small fascia and soffit work is usually better bundled with a roof or gutter project than run as its own mobilisation. If that is your situation we will say so, and price it for doing while the crew and the lift are already on site, which is normally the difference between a modest line item and a minimum charge for a whole day of somebody's time.
Our licensed and insured team brings the right materials and equipment to every job — tapered polyisocyanurate built to a quarter-inch-per-foot fall, hot-air-welded PVC with a KEE plasticizer, tested ANSI/SPRI ES-1 edge metal and coping, two-ply SBS modified bitumen set in cold adhesive, retrofit drains sleeved into existing cast-iron leaders, walk pads routed between rooftop units — and backs the work with a written workmanship warranty. We serve Ontario and nearby communities including Chino, Chino Hills, Montclair, Upland.
What We Handle
Everything our fascia, soffit & edge metal in Ontario covers
One crew, one point of contact, and the full range of fascia, soffit & edge metal work in Ontario, CA. If it is on this list we do it in house rather than handing it to a subcontractor:
- fascia repair
- soffit repair
- rotted fascia replacement
- coil-wrapped fascia
- vented soffit panels
- drip edge
- parapet coping
- ES-1 edge metal
- eave repair
- fascia board replacement
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Ontario services.
Materials, equipment and how we do fascia, soffit & edge metal
The difference between fascia, soffit & edge metal that lasts and fascia, soffit & edge metal that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with tapered polyisocyanurate built to a quarter-inch-per-foot fall, hot-air-welded PVC with a KEE plasticizer, tested ANSI/SPRI ES-1 edge metal and coping, two-ply SBS modified bitumen set in cold adhesive, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Ontario job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in the Inland Empire means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do fascia, soffit & edge metal outside Ontario
Ontario Roof Pros covers Ontario and the surrounding communities of the Inland Empire. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Fascia, Soffit & Edge Metal in Chino, CA — San Bernardino County, population 91,403
- Fascia, Soffit & Edge Metal in Chino Hills, CA — San Bernardino County, population 78,411
- Fascia, Soffit & Edge Metal in Montclair, CA — San Bernardino County, population 37,865
- Fascia, Soffit & Edge Metal in Upland, CA — San Bernardino County, population 79,040
- Fascia, Soffit & Edge Metal in Rialto, CA — San Bernardino County, population 104,026
- Fascia, Soffit & Edge Metal in Colton, CA — San Bernardino County, population 53,909
Start on the Ontario Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Ontario Chooses Ontario Roof Pros
- ✓Core cuts and moisture readings before any recommendation, so the scope is based on evidence rather than a walk-around
- ✓Warehouse and industrial work phased by roof section, with every day's area dried in before the crew leaves
- ✓Proposals name the membrane thickness, insulation, fastening pattern and edge detail, so bids can actually be compared
- ✓We quote the repair beside the replacement and recommend the cheaper one when it is the honest answer
The standards behind fascia, soffit & edge metal
Quality here is not a matter of opinion — it is written down. The fascia, soffit & edge metal work we do in Ontario follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every fascia, soffit & edge metal project in Ontario gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free fascia, soffit & edge metal free estimate in Ontario, or request a quote and we'll get right back to you.